WasherGasketMold.coma Vent Pro NYC service

Brooklyn & NYC · Family-owned

The black ring in your washer door?Gone in one 30-minute visit.

That ring — and the musty towels — is mold living in your front-loader’s rubber door gasket. We do one thing: remove it, treat the seal so it stays gone, and hand you back fresh-smelling laundry. From $149.99.

$50 deposit online, credited to your bill — the rest after the visit.

  • $1M liability insured
  • 110+ five-star Google reviews
  • Same-week appointments
A front-load washer door gasket on one of our Brooklyn visits — heavy black mold along the seal on the left, the same seal cleaned on the right with only faint staining left in the rubber
Before and after — the same gasket, one visit.

Sound familiar?

Four signs it’s the gasket

The gasket’s folds hold water, lint, and detergent after every cycle. Cleaner cycles and vinegar never reach inside them — which is why the smell keeps winning.

  • Towels and clothes smell musty straight out of the wash
  • A black or grey ring inside the rubber door seal
  • Dark spots that survive vinegar, bleach, and “clean washer” cycles
  • A damp, mildewy smell whenever the washer door opens

The 10-second check

Fold the rubber lip back. Go on.

The mold hides in the channel under the seal, where a wipe-down never reaches. If what you find looks like these photos, you’ve found the smell.

A front-load washer door gasket fold pulled back by hand, revealing trapped water and dark mold spots under the rubber lip
Example: standing water and mold spotting under the gasket fold.
Dark mold and detergent grime ringing the channel between the drum and the door gasket of a front-load washer
Our own photo — a Brooklyn front-loader we serviced in August 2026, mold ringing the channel where the gasket meets the drum.

The treatment

Three sprays, a gel, and one tablet.

The sprays are our own solutions — mixed in-house, refined job after job, and chosen to draw as much mold as possible out of the rubber without cracking, drying, or otherwise damaging the seal. What's in them stays our secret; what they do is the point.

  1. First solution, scrubbed in

    We spray the gasket with the first of our in-house solutions and work it into every fold with a scrub brush, then dry the rubber down.

  2. Second solution, dried again

    A second solution goes over the whole seal to keep breaking down what the scrub loosened — then we dry the gasket down again.

  3. Third finishing formula

    Our third formula treats the clean rubber so the seal isn't just mold-free when we pack up — it's a much harder place for mold to move back into.

  4. Mold-stain remover gel

    Wherever staining still shows on the rubber, we coat it with mold-stain remover gel and leave it on to keep working after the visit.

Then one step for you: the tablet

We leave you a machine-cleaning tablet on the way out. About 4 hours after the gel goes on, drop it in the empty drum — no clothes, no detergent — and run the machine's tub-clean cycle. Once that cycle finishes, the washer is ready for regular laundry.

One honest note: removing the black stains isn't guaranteed. Stains soak into the rubber itself, so on most jobs they fade a little rather than disappear — but the mold in and around them is completely gone.

Three unlabeled spray bottles of Vent Pro NYC's own gasket-cleaning solutions lined up on the floor in front of an open front-load washer
Our own photo — the spray lineup, staged before the scrub. Unlabeled on purpose: we mix these solutions ourselves.
A scrub brush resting in the sudsy door-gasket channel of a front-load washer mid-treatment, spray bottles on the floor below
Our own photo — step one in progress: the first solution working in the gasket channel, suds lifting the buildup out.
A drill-driven brush scrubbing foaming cleaning solution around the door gasket of a front-load washer, the drum visible through the open door
Our own photo — the drill-driven brush riding the gasket channel at a Manhattan front-loader, August 2026.
Our own footage from the same visit — the brush making its passes around the seal. Silent clip, about 15 seconds.

What the treatment leaves behind

A customer sent us these two photos of their own machine in September 2026. The mold ring is gone; the faint shadow left in the trough is the deep-set staining we’re upfront about.

Customer photo before cleaning — a heavy ring of black and brown mold along the door gasket trough of a front-load washer
Before — the customer’s own photo of their front-loader.
Customer photo after cleaning — the same washer door gasket with the mold ring removed and only faint staining left in the rubber
After — the same machine, cleaned.

How it works

Booked today, fresh this week

  1. Book online

    Pick a time on the Vent Pro NYC booking page — the gasket service is preselected. A $50 deposit holds the slot and comes off your bill.

  2. One focused visit

    We run the four-step treatment on every fold of the seal — three of our own solutions, then the stain remover gel — and leave you a cleaning tablet for the finishing tub-clean cycle. About 30 minutes, no mess left behind.

  3. Fresh laundry, kept fresh

    Before we leave, we show you the 20-second weekly habit that keeps the gasket dry — so the smell doesn't come back.

Pricing

Two prices. Zero surprises.

$149.99 within 3 miles of our South Brooklyn shop, $199.99 beyond — and adding a dryer vent cleaning to the same visit keeps the gasket at $149.99 anywhere we go.

Front-load washer gasket mold removal$149.99
  • Full gasket inspection + deep clean
  • Mold and mildew removal
  • Detergent residue + lint removal
  • Antimicrobial treatment + cleaning tablet
  • 14-day service guarantee

$149.99 within 3 miles of our South Brooklyn shop; $199.99 beyond, where the difference covers travel time — waived when you add a dryer vent cleaning. You’ll see your exact total before you pay. Online booking takes a $50 deposit, credited to your invoice.

Straight talk

The mold itself is guaranteed gone — that’s the job. The black stains it leaves behind we can’t guarantee: stain soaks into the rubber itself, so on most jobs it fades a little rather than disappears. And if your gasket is torn and actually needs replacing, we’ll say so and refer you to an appliance repair technician we trust instead of charging you for a clean that won’t hold.

Inside a front-load washer's detergent drawer housing before and after our deep clean — dark mold and caked residue along the back and floor before, clean white plastic after
Our own photos — the drawer housing on a Brooklyn front-loader we serviced in September 2026, before and after.

Add on while we’re there

Add the detergent drawer for $29.99

The drawer is only half of it. Water sits inside the drawer housing after every wash — the compartment the drawer slides into — and that’s where the mold really takes hold, in a spot almost nobody can reach. We deep-clean both: the drawer and inside the housing. Mold, mildew smell, and caked detergent gone.

  • Detergent drawer deep-cleaned — mold, mildew, and caked detergent and softener residue removed
  • Inside the drawer housing cleaned too — where water sits after every wash
  • Add it to any washer gasket cleaning visit — only a few extra minutes on site

Pick it as an add-on when you book, or just ask when we’re at your machine.

Book gasket + drawer

Who’s behind this site

The gasket specialists at Vent Pro NYC

WasherGasketMold.com is the washer-gasket service of Vent Pro NYC, a family-owned Brooklyn company that’s kept NYC laundry rooms safe and fresh for over a decade. We’re in front-load washers and dryers all day, every day — gasket mold is our home turf, not a side job.

  • Service area

    Brooklyn first, and homes across NYC.

  • Hours

    Sun–Thu 9 AM–8 PM · Fri until 3 PM · Sat closed

  • Backed by

    $1M liability insurance, a 14-day service guarantee, and 110+ five-star Google reviews.

I had a great experience with Vent Pro NYC. They cleaned my dryer vent and removed the mold from the rubber gasket of my washing machine. They were professional, thorough, and left everything clean. My washer smells fresh again, and my dryer is working much better. I highly recommend them to anyone in Carroll Gardens!
Smadar M. · Verified Google review · Carroll Gardens

FAQ

Quick answers

Will the smell come back?

Not for several months if you leave the door open between loads. We can also show you a quick weekly habit that keeps it gone for good.

Will the black stains disappear completely?

We can't promise that, and we'd rather tell you up front. Black stains soak into the rubber itself, so on most jobs they fade a little rather than vanish — but the mold in and around them is completely removed, and the musty smell goes with it. If the staining bothers you after the mold is gone, a replacement gasket is the honest fix, and we're happy to refer you to an appliance repair technician we trust.

When can I use the washer again?

The same day. We leave you a machine-cleaning tablet: about 4 hours after we apply the finishing gel, drop it in the empty drum — no clothes, no detergent — and run the machine's tub-clean cycle. Once that cycle ends, the washer is ready for regular laundry.

Can you replace the gasket if it's damaged?

No — we clean gaskets, we don't replace them. The good news: most gaskets just need a thorough cleaning. If yours is genuinely torn or worn out, we'll tell you straight, and we work with a technician we trust — we're happy to refer you to an appliance repair company.

Can you clean the detergent drawer too?

Yes — add it to your visit for $29.99. Customers ask for this one a lot: we deep-clean the drawer itself and inside the drawer housing it slides into, where water sits after every wash and mold likes to grow. That housing is the part almost nobody can reach on their own, and it's usually why the smell survives a drawer scrubbing. Just pick it as an add-on when you book, or ask when we're there.

How long does the visit take?

About 30 minutes for a standard front-load washer. It's a focused, single-appliance appointment — many customers add a dryer vent cleaning to the same visit.

Who actually shows up at my door?

Vent Pro NYC — the family-owned Brooklyn company behind this site. We've cleaned dryer vents and washer gaskets across NYC for over a decade. Booking, payment, and receipts all say Vent Pro NYC.

Is this the same as mold remediation?

No. This is routine appliance cleaning of the small rubber door seal on your washer. We don't do building mold remediation — if you have mold on walls, ceilings, or in a basement, that work needs a NYS-licensed mold remediation contractor, and we'll tell you so.

Do I need to do anything before you arrive?

Just make sure the washer is empty and reachable — we bring everything else and work clean. Afterward there's one small job for you: about 4 hours after the visit, run the cleaning tablet we leave you through a tub-clean cycle (empty drum, no detergent). Once it finishes, the machine's ready for regular laundry.

Why does booking show $199.99 for my address?

On its own, the visit is $149.99 within about 3 miles of our South Brooklyn shop and $199.99 beyond — the difference covers our travel time, and you see the exact total before you pay. Add a dryer vent cleaning to the same visit and the gasket stays $149.99 wherever you are.

Your next load could smell like clean laundry again.

Same-week appointments across Brooklyn & NYC. Book online in 60 seconds, or call and we’ll set it up for you.